6
The fuse cover must be retted
when changing a fuse and if
the fuse cover is lost the plug
must not be used until a cor-
rect replacement is tted.
Correct replacement are identi-
ed by the colour insert or the
colour embossed in words on
the base of the plug.
Replacement fuse covers are
available from your local elec-
trical store.
For the Republic of Ireland
only
The information given in
respect of Great Britain will
frequently apply, but a third
type of plug and socket is also
used, the 2-pin, side earth
type.
Socket outlet / plug (valid for
both countries)
If the tted plug is not suitable
for your socket outlet, please
contact After-sales Service for
further instruction. Please do
not attempt to change plug
yourself. This procedure needs
to be carried out by a qualied
technician in compliance with
the manufactures instructions
and current standard safety
regulations.
CORRECT USE
Do not exceed the maximum
load allowed. Check the maxi-
mum load allowed in the
programme chart.
Do not dry unwashed items in
the tumble dryer.
Do not overdry the laundry.
Take care that no lint or dust is
accumulated around the dryer.
identical one. The power cable
must only be replaced by a
qualied technician in compli-
ance with the manufacturer
instruction and current safety
regulations. Contact an author-
ized service centre.
Do not operate this dryer if it
has a damaged mains cord or
plug, if it is not working prop-
erly, or if it has been damaged
or dropped. Do not immerse
the mains cord or plug in
water. Keep the cord away
from hot surfaces
The electrical components
must not be accessible to the
user after installation.
Do not touch the dryer with
any wet part of the body and
do not operate it when bare-
foot.
ELECTRICAL CONNECTION
FOR GREAT BRITAIN AND
IRELAND ONLY
Fuse replacement.
If the mains lead of this dryer is
tted with a BS 1363A 13amp
fused plug, to change a fuse in
this type of plug use an A.S.T.A.
approved fuse to BS 1362 type
and proceed as follows:
1. Remove the fuse cover (A)
and fuse(B).
2. Fit replacement 13A fuse into
fuse cover.
3. Ret both into plug.
Important:
If, due to lack of space, the
dryer must be installed directly
next to a gas or coal stove, a
heat insulating plate (85 x 57 cm)
must be installed in between
and the side of the plate facing
the stove must be covered
with aluminium foil.
The dryer is not designed for
built-in installation.
The dryer can be installed
under a worktop, provided
that adequate ventilation of
the dryer is assured. Install a
ventilation grid (minimum 45
cm x 8 cm), in the rear part of
the worktop under which the
dryer is installed.
ELECTRICAL WARNINGS
Make sure the voltage speci-
ed on the rating plate corre-
sponds to that of your home.
For installation to comply with
current safety regulations, an
omnipolar switch with mini-
mum contact gap of 3mm is
required.
Regulation require that the
dryer is earthed.
For dryers with tted plug, if
the plug is not suitable for you
socket outlet, contact a quali-
ed technician.
Do not use extension leads,
multiple sockets or adapters.
Do not connect the dryer to a
socket which can be operated
by remote control.
The power cable must be long
enough for connecting the
dryer, once tted in its hous-
ing, to the main power supply.
Do not pull the power supply
cable.
If the power cable is damaged
it must be replaced with an
(8 Seiten)
(8 Seiten)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern