Bauknecht B CT 63F LY X Betriebsanweisung Seite 2

  • Herunterladen
  • Zu meinen Handbüchern hinzufügen
  • Drucken
  • Seite
    / 2
  • Inhaltsverzeichnis
  • FEHLERBEHEBUNG
  • LESEZEICHEN
  • Bewertet. / 5. Basierend auf Kundenbewertungen
Seitenansicht 1
CLEANING AND MAINTENANCE
CLEANING
Do not use steam-cleaning equipment.
Disconnect the appliance from the mains.
Important: do not use corrosive or abrasive detergents. If any such
products unintentionally come into contact with the appliance, clean
the appliance immediately with a damp cloth. Do not use alcohol.
Clean the surfaces with a damp cloth. If it is very dirty, add a few
drops of washing-up detergent to the water. Finish o with a dry
cloth.
Important: do not use abrasive sponges or metallic scrapers or
scourers. Over time, these can ruin the enamel surfaces.
Use detergents specically designed for cleaning the appliance
and follow the manufacturer's instructions.
Important: clean the lters at least once a month to remove oil and
grease residue.
MAINTENANCE OF THE GREASE FILTERS
This must be cleaned once a month using non aggressive detergents,
either by hand or in the dishwasher, which must be set to a low
temperature and a short cycle.
When washed in a dishwasher, the grease lter may discolour slightly,
but this does not aect its ltering capacity.
Pull out the handle to remove the lter.
Once the lter has been washed and left to dry, proceed in reverse
order to ret the lter.
MAINTENANCE OF THE CHARCOAL FILTER
(FOR FILTRATION MODELS ONLY)
This lter retains the unpleasant odours produced during cooking.
Saturation of the carbon lter occurs after a relatively long use,
however this depends on the type of cooking and how regularly
the grease lter is cleaned. Regardless, it is necessary to replace the
cartridge every 4 months. It CANNOT be washed or recycled.
Fitting or replacing the carbon lter
1. Disconnect the hood from the mains.
2. Remove the grease lters.
3. Fit 2 carchoal lters (one each side of the conveyour), snap into
place.
4. Reinstall the grease lter in place.
Proceed in reverse order to remove.


REPLACING THE LAMPS
Disconnect the appliance from the electricity.
Prior to touching the light bulbs ensure they are cooled down.
Remove the grease lters to access the lamp area.
Replace the damaged lamp.
Use E14 3W max LED lamps only. For more details, check enclosed
leaet “ILCOS D” (alfanumeric position “1d”).
Note: For replacement LED, please contact the Technical After-sales Service
Centre.
TROUBLESHOOTING
Problem Solutions
The appliance does not work. Check the mains voltage and whether the appliance is connected to the power supply;
Check that a speed has been selected;
Switch the appliance o and on again to see if the fault persists.
The hood is not extracting air suciently. Check that the air extraction speed is set to the desired level;
Check that the lters are clean;
Check the air vents for any obstructions.
The hood has turned o during normal
functioning.
Check that the power has not been disconnected;
Check that the omnipolar disconnection device has not tripped.
You can download the Safety Instructions, User Manual, Product Fiche and Energy data by:
Visiting our website docs . bauknecht. eu
Using QR Code
Alternatively, contact our After-sales Service (See phone number in the warranty
booklet). When contacting our After-sales Service, please state the codes provided on
your product's identication plate.
XXXXXXXXXXXXXX
Model
xxxxxxxxxxxx
XXXXXXXXXXXXXX
Model
xxxxxxxxxxxx
400011282341
* Available only on certain models
Seitenansicht 1
1 2

Kommentare zu diesen Handbüchern

Keine Kommentare